OPERATING MODE
DMX Control
DMX mode, receive DMX signal, RDM signal
Auto Run
Fixture run automatically according to built-in programs
Sound Control
When the fixture detects a strong sound, the fixture automatically runs a scene according to the built-in program, otherwise it will stay the last scene
Scene Mode 01
runs in a set scebe, which supports most of the custom editing of 10 scenes.
1~10
outputs the specified scene
Auto
Automatically loops the output scene in the set scene time (non-zero) order, and the scene with time 0 automatically ignore
M/S Choose
Master and slave selection, non-DMX mode takes effect, select the mode of data output, fixture detect DMX cable state automatic switch output, prevent data conflicts
Master
Fixture runs built-in program. If DMX has no signal, it outputs data (synchronization), otherwise it does not output data.
Slave
Fixture runs built-in program and do not output data
Auto
If DMX has no signal, the fxiture will runs built-in program. Otherwise,
the fixture will run in DMX Mode(follow DMX).
Lamp Switch
(Lamp light source) pop-up confirmation dialog box, select "SURE" to confirm the current operation, turn on or off the lamp, switch time interval limited to 30 seconds
Off
The current lamp output is off
On
The current lamp output is turned on
DISPLAY SETTING
Language
Display language settings
English
English display
Chinese
Chinese display
Screen Saver
Set screen 30 seconds without operation, the screen's display content or method.
OFF
Keep the last operation page
Mode1
Black
Mode2
Black screen, showing the address code of the current fixture in the lower left corner.
Mode3
Display trademark information, address code and operation mode.
Screen Rot
Set the display direction of the screen.
OFF
No reverse display
ON
Reverse display
DMX Indicate
Set the indication mode of DMX signal indicator.
Mode1
When signal is bright, no signal is off.
Mode2
When signal is off, no signal is bright.
Mode3
When signal is flash, no signal is off.
Screen Light
Set the screen backlight for 10 seconds without operation
1~10
10
Installation Instructions
CABLE CONNECTION DMX
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24AWG, low capacity. Do not use microphone cable or other cable withcharacteristics differing from those specified. Theendconnections must be made using XLR type3 or 5-pin male/female connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4W)between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the shield braid and to pin 1 of the connectors.
RIGGING(OPTIONAL)
This equipment can be positioned and fixed by clamp in every direction of the stage. Locking system makes it easy to fasten to the bracket.
Attention! Two clamps is needed to fix the equipment. Every clamp is locked by fastener of 1/4 kind. Fastener can only be locked clockwise.
Attention! Fasten a safety string to the additional hole of side aluminum piece. The secondary accessory can not hang on the delivery handle. Nip the equipment on bracket.
Check if rigging clamp (not including the one inside) damaged or not? If stand ten times weight as the equipment. Make sure the architecture can stand ten times weight as all the equipments, clamps, wirings and other additional fixtures.
Screws for clamping must be fixed firmly. Take one M12 screw (Grade 8.8 or higher) to clamp bracket, and then screw the nuts.
Level the two hanging points at the bottom of clamp. Insert fastener to the bottom, lock the two levers by 1/4 rotating clockwise; then install another clamp.
Install on safety string which stands at least ten times weight as equipment. Terminal of the accessory is designed for clamps.
Make sure pan/tilt lock unlocked or not. Keep the distance more than 1M from equipment to flammable material or lighting source.
Panel Operation
BRIEF
The light panel diagram show as Figure 3, above area is fixture description, below area show fixture real-time status, such as DMX cable status, lamp status, error or information(ps. when there are message hav't been checked, echo 'ERR' in status bar, otherwise echo 'NOR'). Display & operation just like 'Android operation system', when select or set item value, system save the settting immediately. RDM protocol is embed in fixture, user set DMX address via cable using the controller surpport RDM function. when fixture was search by controller, displayer will echo 'RDM' indicate this RDM is work.
OPERATION
Operate fixture with touch or encoder/button
The left area is TFT Displayer and touch(product which support touch), chick item or value with finger will to complete operation of set light setting(parameters) or view light state.
The area on the right hand side is rotary encoder with button or key, As auxiliary input interface, if fixture disable touch function, the encoder/key can been choose to set or view the item, and then press the encoder button/key to confirm the selection, rotary
encoder or push key again set the parameter value, finally, Press encoder button/key one again to save value or setting.
Parameter value setting
When the selected item is value need to been modified, the dialog shown in Figure 4 will pop up.
Modify value : Can quickly modify value via pull the slider to the desired position, or click the button of 'up' or 'down' whit finger on the right side to set the exact desired value, another way is roll encoder on the right hand side of panel.
Apply value : When Value had been modified, Then press the bottom of 'apply' in the left corner to apply to the light, but haven't saved;
Save Value : Any time, click on the lower right corner of the "OK" button, the setting will been saved into internal memory.
Boolean parameter setting
when the selected parameters is a Boolean value (such as ON or OFF), can directly modify setting by chick corresponding item, the setting will been saved right now.
When the parameter is a key item, chick corresponding item, a dialog shown in Figure 5 will been popup ask for the confirm. Chick 'sure' to confirm.
Sub Menu(Parameter)
Detailed Photos
Packaging & Shipping
PACKING LIST
Product Name
Quantity
Moving Head Light
1 PCS
Power-line
1 BASE
User Manual 1 PCS
